- #Imac 27 late 2013 hard drive snesor how to
- #Imac 27 late 2013 hard drive snesor update
- #Imac 27 late 2013 hard drive snesor upgrade
- #Imac 27 late 2013 hard drive snesor windows
Next, if you have a Time Machine backup and are luckier then me, you can restore it.
Now, you really need to open it up again and make sure all the adhesive is removed, then you need to apply the new supplied adhesive to seal the screen back to the chassis permanently.Īfter sealing up the screen, power back into recovery mode. Run disk utility and format the new drive. If your iMac doesn’t boot into recovery mode, power it off and then on again, pressing down Command + R after powering it on. I removed the top right hard drive mounting screw so that I could swing the cable around for a better connection.Īt this point you gently put the screen back and test if it works. Here is how the new drive looks installed with the Thermal Sensor Cable. Next, you will need to transfer the 4 mounting peg screws to the new drive adapter. When removing these 2 Hard Drive mounting screws, be careful not to drop them into the power supply!Īfter you get the hard drive out, you can remove the small bracket on the left side. Next you’ll need to loosen the left speaker screws(I did not remove them) so that you can gain access to the 2 left hard drive mounting screws. One has a pull tab and the other has two side tabs you need to squeeze while pulling. Once you get the screen down, you will need to carefully disconnect the 2 screen cables on the right side. I had a nice big sift towel waiting to lay the screen on and I also used a roll of paper towels to support the screen. You can either use the supplied suction cups or your fingers to gently pry the screen away and then down from the main chassis. You’ll hear the adhesive as you work through it.Īt this point you should feel the screen separating a bit from the chassis. I worked it around twice and was careful not to go too deep by the webcam. This step would be a little easier with two people, one to work the pry tool and then one to get the “Guitar Pick” in. Then you work the “Guitar Pick” in and start using that to separate the screen from the chassis(green line in pic below for illustration). Next, I started the screen separation by taking the green pry tool and working it in gently to start prying the glass which is attached with adhesive to away from the chassis. I unboxed all my parts and I attached the SSD onto the Sabrent Cradle adapter using the smaller countersunk supplied screws.
I watched the YouTube video above a few times to get familiar with the process. I also need to purchase this Sabrent 2.5” SSD & SATA Hard Drive to Desktop 3.5” SATA Bay Converter Mounting Kit (BK-PCBS) so that the 2.5″ SSD woud mount correctly where the previous 3.5″ 1TB Seagate Drive was. There are some DIY hacks to get around this without purchasing the cable, but OWC is a company I trust and I didn’t want to risk shorting anything out. Without that special Thermal Sensor Cable, apparently your iMac will spin the Hard Drive cooling fans up and make a lot of noise.
#Imac 27 late 2013 hard drive snesor upgrade
If you have some of these parts or tools laying around, then you could get away with purchasing this kit instead: OWC In-line Digital Thermal Sensor for Hard Drive Upgrade for 27″ iMacs 2012 and Later To make my life easier I order the OWC Complete Hard Drive Upgrade Kit Including Tools for all 27″ iMacs 2012 & Later for about $53.
#Imac 27 late 2013 hard drive snesor update
Last update on / Affiliate links / Images from Amazon Product Advertising API
#Imac 27 late 2013 hard drive snesor how to
There are several detailed YouTube videos that show you how to do this I used the following one from OWC and watched it a few times to get familiar with the “surgery”. You need to separate the screen from the main chassis. You can still open it up, but the process it a bit more involved as there are no screws to gain access inside.
#Imac 27 late 2013 hard drive snesor windows
Unlike like most of the Windows PCs I worked on during my IT career, you can’t just simply open up an iMac and swap out the hard drive. If you want to read more about Fusion Drives, checkout this wikipedia link: These 2 drives appear and act as one volume on your iMac and the system takes care of moving/caching your most frequently used files onto the faster SSD drive. My iMac 27 Late 2013 had the Fusion drive which is basically a 1TB Seagate Hard Drive paired with a 128GB SSD Drive(for the late 2015 iMac models Apple has reduced the size of the SSD drives to only 24GB for the 1TB combo). ? I tried booting into Recovery Mode (turn power on and the hold Command + R) and running Disk Utility, but it was never able to repair the drive. On Cyber Monday, it finally it “Gave up the Ghost” as they say and would no longer boot. I was having some previous random issues on my iMac where Chrome would lock up and sometimes the whole system would lock up, But, I kept blaming it on the 50 – 60 tabs I usually had open in Chrome ? Well, I really wasn’t planning on doing an iFusion Hard Drive Replacement with SSD post, but my hard drive failed earlier this week!